Furuno Network Sounder DFF3 Instrukcja Użytkownika

NETWORK SOUNDERDFF3OPERATOR'S MANUALwww.furuno.co.jpMODEL

1. MOUNTING32k/2k 28/50 Steel 28F-1850B-12TFB-7000(2) T-634FRP TRB-1100(2) T-634-F28/82 Steel 28F-1882B-35RTFB-7000(2) T-636FRP TRB-1100(2) T-636-F28

1. MOUNTING42k/3k 28/150 Steel 28F-18150B-12HTFB-7000(2) T-637FRP TRB-1100(2) T-637-F50/107 Steel 50B-12100B-10RTFB-7000(2) T-643FRP TRB-1100(2) T-64

1. MOUNTING53k/3k(con’t)28/88 Steel 28BL-12HR88F-126HTFB-7000(2) T-682FRP TRB-1100(2) T-682-FSteel 28F-24H88F-126HTFB-7000(2) T-682FRP TRB-1100(2) T-

1. MOUNTING63k/3k(con’t)50/200 Steel 50BL-24H200B-12HTFB-7000(2) T-695FRP TRB-1100(2) T-695-FSteel 50BL-24HR200B-12HTFB-7000(2) T-683FRP TRB-1100(2)

1. MOUNTING72k (con’t) 50 Steel 50B-12 TFB-5000(1) T-611FRP TRB-1000(1) T-611-FSteel 50BL-12 TFB-5000(1) T-702FRP TRB-1000(1) T-702-FSteel 50BL-12HR

1. MOUNTING81.2 Network SounderThe network sounder can be installed on a desktop, deck or on a bulkhead. When selecting a mounting location for the n

1. MOUNTING9• A magnetic compass will be affected if the network sounder is placed too close to it. Observe the compass safe distances noted in the

1. MOUNTING101.5 Optional Temperature Sensors1.5.1 Transom mount temperature sensor T-02MTB• Fix the cable at a convenient location with cable clamp

1. MOUNTING111.5.2 Thru-hull temperature sensor T-02MSB, T-03MSBSelect a suitable mounting location considering the following points:• Select a mid-

122. WIRING2.1 Wiring OutlineConnect the power cable, transducer cables, sensor cable, network cable and ground wire to their respective locations on

iIMPORTANT NOTICES• The descriptions in this manual are intended for readers with a solid knowledge of English.• No part of this manual may be copie

2. WIRING132.2 Transducer CableTD-ID transducer (Airmar make transducer)The TD-ID type transducer can be connected to this equipment. However, note t

2. WIRING144. Connect the transducer cable to the WAGO connector, following the instructions in the figure below and the interconnection diagram. (Th

153. INITIAL SETTINGS3.1 Tap SettingThis equipment is preprogrammed for use with certain transducers. A jumper wire inside the equipment is set accord

3. INITIAL SETTINGS163.2 DIP Switch SettingThe DIP switch S2 sets up the system according to the equipment connected. In the default setting all swit

3. INITIAL SETTINGS17DIP SW S2 setting, sounder and IP addressTransducer setting at NavNet/NavNet3DAfter setting up the transducer at the DFF3, set t

3. INITIAL SETTINGS183.3 Operation CheckFor NavNet, the DFF3 is powered on/off from ship’s switchboard. For NavNet 3D, it is powered on/off from the

194. MAINTENANCE4.1 MaintenanceRegular maintenance is essential for good performance. Check the items listed in the table below at the suggested inter

4. MAINTENANCE204.2 Replacing the FuseThe 5A fuse (Type: FGBO-A 125V 5A PBF, Code No. 000-155-853-10) in the snap-in fuse holder on the power cable p

ＰＡＣＫＩＮＧ　ＬＩＳＴ02GF-X-9851 -0 DFF3-J/EN A M EO U T L I N EDESCRIPTION/CODE №Q'TY1/1ユニット UNITﾈｯﾄﾜｰｸ魚探NETWORK SOUNDERDFF3000-011-916-001予備品 SPARE PART

FURUNO DFF3 SP - 1 E2037S01A 080318 SPECIFICATIONS OF NETWORK SOUNDER DFF3 1 GENERAL 1.1 TX frequency 28-200 kHz, two frequencies alternately tr

ii SAFETY INSTRUCTIONSDo not operate the equipment with wet hands.Electrical shock can result.Do not place liquid-filled containers on the top of the

Jan.18'08 R.EsumiD-1

243A1BCDRAWNCHECKEDAPPROVEDDWG.No.TITLENAME名称INTERCONNECTION DIAGRAM相互結線図REF.No.SCALE MASSkgC2037-C01- AT.YAMASAKIDFF3ネットワーク魚探NETWORK SOUNDER02-161-10

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

SAFETY INSTRUCTIONSiiiStandardcompassSteeringcompass 0.95 m 0.60 mCAUTIONCAUTIONThe transducer cable must be handled carefully, following t

ivTABLE OF CONTENTSFOREWORD...vSYSTEM

vFOREWORDA Word to the Owner of the DFF3Congratulations on your choice of the FURUNO DFF3 Network Sounder. We are confident you will see why the FURUN

viSYSTEM CONFIGURATIONBasic configuration shown with solid line.100/110/115/220/230 VAC1φ, 50/60 HzNetwork SounderDFF312-24 VDCLow Freq.TransducerHigh

11. MOUNTING1.1 Equipment ListsStandard supplyOptional supplyName Type Code No. Qty RemarksNetwork Sounder DFF3—1Spare Parts SP02-05601 001-033-740 1

1. MOUNTING2Transducer, thru-hull pipe and tank combinationsOutput(W)Frequency(kHz)Ship type TransducerThru-hull pipeTank1k/1k 28/50 Steel 28F-850B-9