Furuno Multi Instrument FI-504 Instrukcja Użytkownika

www.furuno.co.jpFI-504 MULTIInstrument

1. OPERATION21.2 Turning the Power On/OffTo power the instrument, press the DISP key. All LCD segments go on and off and then the last-used display ap

1. OPERATION31.4 Selecting a DisplayUse the DISP key to select a display category. Select desired display with the MODE key.HEADINGCurrent headingAver

1. OPERATION41.4.1 Display descriptionDepth categorySpeed categoryDisplay title Indication FunctionCurrent depth DPTH Current depth, in meters, feet o

1. OPERATION5Timer categoryWind categoryBeaufort no. and wind speedDisplay title Indication FunctionCount up timer UP Count-up timer.Count down timer

1. OPERATION6Heading categoryNavigation categoryDisplay title Indication FunctionCurrent heading HDG Heading, in degrees. Bearing reference in Magnet

1. OPERATION7Environment categoryAutopilot categoryEngine categoryNote: In case of multiple engines, the data of desired engine number (max. eight, E0

1. OPERATION81.5 Selecting Apparent or True Wind Angle,Wind SpeedYou can show wind angle and wind speed in apparent or true wind. The apparent wind is

1. OPERATION91.7 AlarmsThere nine conditions which trigger audio and visual alarms: Shallow alarm, Deep alarm, Shallow anchor alarm, Deep anchor alarm

1. OPERATION102. If the selected alarm page shows “Off,” press and hold down the SELECT/CLEAR key until an alarm setting appears.3. Press the APP/TRUE

1. OPERATION111.8 TimersThree timers are provided:• Count-up timer (stopwatch)• Count-down timer (two provided)Time is displayed in seconds or minutes

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

1. OPERATION12To stop or restart the timer, press the SELECT/CLEAR key momen-tarily. A short beep sounds when the timer is stopped or restarted.To sto

132. MAINTENANCE,TROUBLESHOOTINGThis chapter provides the information necessary for keeping your equip-ment in good working order.2.1 Preventive Maint

2. MAINTENANCE, TROUBLESHOOTING142.2 TroubleshootingIf you feel the equipment is not functioning properly, follow the proce-dures in the table below t

153. INSTALLATION3.1 Equipment ListsStandard supplyOptional supplyName Type Code No. Qty RemarksDisplay Unit FI-504 - 1InstallationMaterialsCP26-00600

3. INSTALLATION163.2 MountingThe display unit can be installed two ways: surface mount (fixed at front panel or fixed from rear panel) and flush mount

3. INSTALLATION17Surface mount 2: Fix instrument from rear panel1. Using the template at the back of this manual, open a mounting hole in the installa

3. INSTALLATION183.3 Wiring3.3.1 Standalone configurationFor standalone configuration the junction box is not necessary; connect the instrument direct

3. INSTALLATION19Junction box (option)The junction box is required when connecting NMEA 2000 network. This section covers wiring of the junction box.

3. INSTALLATION20Terminal resistorThe illustration below show various system configurations and what units to activate the terminal resistor.= Termina

3. INSTALLATION21Turn on the terminal resistor in the junction box when the NMEA 2000 sensor(s) connected to it do not have a terminal resistor.For ho

iIMPORTANT NOTICES• The descriptions in this manual are intended for readers with a solid knowledge of English. • No part of this manual may be copied

3. INSTALLATION22.3. Use the APP/TRUE or SELECT/CLEAR key to set value or select option.VMG key: Decrement valueSELECT/CLEAR key: Increment value or s

3. INSTALLATION23Setup1 menu itemsDisplay FunctionSetting range or optionsDefaultsettingSelect depth unit. M (Meter),FT (Feet)MSet depth offset. -99 -

3. INSTALLATION24Set speed response. The lower thesetting the faster the response to change in speed.0 - 12 0Set SOG response. The lower thesetting th

3. INSTALLATION25Select true or magnetic bearing. MAG (Magnetic),TRU (TrueMAGSelect heading type to display whenactivating locked heading.LOC (Locked)

3. INSTALLATION263.4.2 Setup2 menuThe setup 2 menu contains user settings which once preset do not re-quire frequent adjustment. 1. Press and hold dow

3. INSTALLATION27Setup2 menu itemsDisplay FunctionSetting range oroptionsDefaultsettingSoftware version of CPU1.XX=program no. and xxx=program version

3. INSTALLATION28Turn timer displays on/off. ON, OFF ONTurn wind displays on/off. ON, OFF ONTurn heading displays on/off. ON, OFF ONTurn navigation di

FI-504 MULTI E7269S01A SP-1SPECIFICATIONS OF FI-504 MULTI 1 GENERAL 1.1 Display Segment LCD 1.2 Display Content Depth, speed, wind speed, wind

NAME OUTLINE Q'TYDESCRIPTION/CODE №ＰＡＣＫＩＮＧ ＬＩＳＴ26AA-X-9860 -1 FI-5041/1NAME OUTLINE Q'TYDESCRIPTION/CODE №ユニット UNIT表示部MONITOR UNIT1FI-504000

CODE NO.000-010-619-00TYPEFI-50-FLUSH-KIT略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-3 26AA-X-9401INSTRUMENTSFI-50ﾌﾗｯｼｭﾏｳﾝ

SAFETY INSTRUCTIONSiiWARNINGIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.CAUTIONIndicate

Jul.24'07 R.EsumiD-1

Jul.24'07 R.EsumiD-2

Jul.24'07 R.EsumiD-3

12345SHIELDNET-SNET-CNET-HNET-LDROP12345SHIELDNET-SNET-CNET-HNET-LDROP12345SHIELDNET-SNET-CNET-HNET-LDROP12345SHIELDNET-SNET-CNET-HNET-LDROP12345SHIEL

タッピンネジ用穴（4ヵ所）For tapping screws (4 pcs.)寸切りボルト用穴（2ヵ所）For bolts (2 pcs.)

FI-50シリーズ 表示部 フラッシュマウント用型紙FI-50 series Display unit Flush Mount Template

iiiTABLE OF CONTENTSFOREWORD... ivSYSTEM CONFIGURATION ...

FOREWORDivFOREWORDA Word to the Owner of the FI-504Congratulations on your choice of the FURUNO FI-504 Multi Display, a member of the FI-50 series of

vSYSTEM CONFIGURATIONStandalone configurationNOTICE: Turn on the terminal resistor in the instrument when connecting an NMEA 2000 sensor. For the proc

SYSTEM CONFIGURATIONviNMEA 2000 networkNOTICE: Turn on the terminal resistor in the terminator of the NMEA 2000 network.FI-501*and/orFI-502FI-5001WIND

11. OPERATIONProvided applicable sensors are connected, the FI-504 provides the fol-lowing information, all on a backlit LCD:•Depth• Speed• Heading• E