Furuno FR1500 Mk3 Instrukcja Użytkownika

MARINE RADARFR-1505/1510/1525 MARK-3

viiiSYSTEM CONFIGURATIONDISPLAY UNITRDP-119ATA Board (ARP-17) orARP Board (ARP-10)*1GPSSpeed LogGyrocompassGyro ConverterGC-8AOptionRemote DisplayFMD

1-1MOUNTING1.1 Scanner UnitMounting considerations• The scanner unit is generally installed either on top of the wheelhouse or on theradar mast, on a

1-2Assembling the scanner unitThe scanner unit consists of the scanner radiator and the scanner unit chassis,and they are packed separately. Fasten th

1-3O-ringRadiator bracketWaveguideAntenna radiatorHex bolt (M8X40), 8 pcs.(XN20AF, XN24AF only) Guide pin(XN20AF,XN24AFonly)Hex bolt (M8X35), 8 pcs.

1-41. Construct a suitable mounting platform referring to the outline drawing at theback of the manual.2. Drill four mounting holes of 15 mm diameter

1-51.2 Display UnitMounting considerationsThe display unit can be mounted on a tabletop or a bulkhead. When selecting amounting location, keep in min

1-6bulkhead mounting1. Remove the fixing plate, mounting base, bottom plate and cover.2. Fasten the mounting base and bottom plate at the top of the d

2-1WIRING2.1 Scanner Unit1. Open the scanner unit cover.2. Disconnect plugs P611, P801 and P821.3. Unfasten the transceiver module (two bolts). Remov

2-2Figure 2-2 Scanner unit, front view, cover removed5. Pass the signal cable through the cable entry hole in the scanner unit mountingplatform. Trim

2-3Figure 2-4 Scanner unit, front view13.Confirm that all screws are tightened and all wiring is properly mode. Coatwaterproofing gasket, bolts and t

C 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 Your Local Agent/Dealer All rights re

2-4Fabricating signal cable S03-811. Remove the vinyl sheath by 450 mm.2. Slide the clamping ring, washer, rubbergasket and washer onto the signal ca

2-52.2 Display UnitAt least two cables are terminated at the display unit: the signal cable S03-81 andthe power cable. The signal cable comes with a

2-6Wiring1. Remove the display unit cover.Figure 2-9 Display unit, rear view, cover removed2. Dismount the clamping plate from the cable clamp by loo

2-76. It is recommended to seal the cable gland with aluminum tape or similar mate-rial to keep foreign objects out of the display unit.Figure 2-11 D

2-8GroundConnect a ground wire (IV-8sq or equivalent) between the earth terminal on thedisplay unit and ship’s superstructure.Ground the equipment to

2-92.4 Change of DC Power SpecificationsThe power specification (12 V, or 24/32 V) of the DC POWER Board for the FR-1505 MARK-3 can be modified in th

2-10Connections on transformer T1Note: Make sure that the conductor of the transformer flying wire WHITE (B) doesnot not touch U1.Figure 2-15 Connect

2-112.5 Change of AC Power SpecificationsThe AC display unit is shipped from the factory ready for connection to a 100 VACpower supply. To operate th

2-12 Ship's MainsJumper WireJP1 JP2 JP3 JP4100 VAC YES YES YES NO220 VAC NO NO NO YESFigure 2-18 AC POWER Board8. Mount the display unit cove

3-1EXTERNAL SIGNAL INPUT, OUTPUT3.1 External InputAll external equipment and the antenna unit are connected to the SPU Board.Several connectors are o

iSAFETY INSTRUCTIONS

3-2Table 3-1 Input connectors on the SPU BoardNote 1: HDT, VHW, HDG, HDM. NMEA-HDG connector also accepts, water tem-perature and water depth data (

3-3Table 3-2 Output connectors on the SPU BoardSignal NameSlave displayBuzzer signalTarget signal (serial data)Conn. NameEXT RADAREXT ALARMNAV 1Conn.

3-43.4 Data SentencesTable 3-3 NMEA-0183 input sentencesItem Receive SentenceSpeed (knots only) RMA>RMC>VTG>VHWHeading (true) HDT>HDG(*)&

4-1INSTALLATION OF OPTIONAL EQUIPMENT4.1 Gyro Converter GC-8AThe GYRO CONVERTER GC-8A mainly consists of the GYRO CONVERTERBoard, which is installed a

4-2Mounting, connection1. Remove the rear cover.2. Attach four spacers as shown below.Gyro ConverterBoard 64P1106Gyro ConverterBoard 64P1106SpacerFuse

4-3Connection of external power supplyAn external power supply is necessary when the repeater signal is step-by-steptype and the step voltage is below

4-4Setting method 1: by gyrocompass specifications1) Gyrocompass type 2) FrequencyGyrocompasstypeSW1-4SW1-5SW1-6JP1 Frequency SW1-7SW1-8RemarksAC sync

4-5Setting method 2: by make and model of gyrocompassrekaMsledoMnoitacificepSWS1-1WS2-1WS3-1WS4-1WS5-1WS6-1WS7-1WS8-1WS1-2WS2-2WS3-21PJ2PJ3PJ4PJ5PJONU

4-6Location of DIP switches, jumper wires on the GYRO CONVERTERBoardFigure 4-3 GYRO CONVERTER BoardSetting the bearing on the radar displayConfirm tha

4-74.2 Automatic Tracking Aid ARP-17Necessary partsTable 4-2 Contents of ARP-17-2-E installation kit (Code No. 008-488-840)Name Type Code No. QtyATA B

ii

4-8Adjustment1. Set the controls on the radar as follows:Range: 6 nmA/C SEA, A/C RAIN, GAIN: fully counterclockwise2. Connect a digital multimeter, se

4-96. Press the [6] key several times to select QV from the VIDEO field and pressthe [ENTER /SELECT] key.7. Adjust potentiometer R120 (“LEVEL”) on the

4-10Video signal checkFigure 4-9 Video signal checkDiagnostic testConduct the diagnostic test (keying sequence: [MENU] [0] [0] [0] [0] [2] [2] tocondu

4-114.3 Automatic Tracking Aid ARP-10Necessary partsTable 4-3 Contents of ARP-10 installation kit ARP-10-A (Code No.: 000-086-996)Name Type Qty Code N

4-124.4 Video Plotter RP-17Necessary partsTable 4-4 Contents of RP-17-15E-2 Installation kit (Code No. 000-086-993)emaNepyTytQ.oNedoCksiDyppolFXX12519

4-135. Unfasten eight screws to remove the cover.6. Fasten the RP-17 Board with five panhead screws.7. Connect the cable assy. between J106 on the SPU

4-14Figure 4-15 How to wire and solder the autopilot cable8. Reattach the display unit cover.9. Referring to the Operator's Manual, conduct the s

4-154.5 RGB BUFFER (External Monitor Interface)The RGB BUFF Kit provides for connection of an external monitor, and mainlyconsists of the RGB BUFF Boa

4-165. Connect the XH connector assembly (supplied) between J501 (13P) on theRGB BUFF Board and J108 (13P) on the SPU Board.6. Bind XH connector with

4-175. Solder the VH connector (supplied) to the line from the PM-30 and connect itto J403 on the PM-INT Board.6. Connect the XH connector (supplied)

iiiTABLE OF CONTENTSEQUIPMENT LISTS ... ivSYSTEM CONF

5-1INITIALIZATION AND ADJUSTMENT5.1 Opening the Installation MenusThe display unit RDP119 can be used as a sub display. If the sub display isinstalled

5-25.2 Tuning1. Press [MENU] [0] [0] [0] [0] [5] [5] [0] [0] to display the SET UP 2 menu.2. Press the [9] key to select TUNE SET.3. Press the [ENTER/

5-35.4 Sweep TimingSweep timing differs with respect to the length of the signal cable between thescanner unit and the display unit. Adjust sweep timi

5-45. Press the [ENTER/SELECT] key to automatically adjust the video level. Whenthe adjustment has been completed a beep sounds (R-type only).6. Conne

5-5VIDEO SIGNALVideo LevelApprox. 4.0 Vpp ±0.2 VGate for videoadjustmentVideo LevelApprox. 4.5 VppMain BangAdjust the EEPOT (U92) on the pcb 03P9230 s

5-65.7 Confirming Magnetron Heater VoltageMagnetron heater voltage is adjusted at the factory. However, confirm that it iswithin the prescribed rating

5-75.8 Other Items on the Installation MenusSET UP 1 menuKeying sequence: [MENU] [0] [0] [0] [0] [5] [5]2. HDG ADJ: Aligns heading.3. TIMING: Adjusts

5-84. ON TIME, 5. TX TIME: Shows number of hours the radar has been turned onand transmitted, respectively. Value can be changed.6. RNG UNIT: Selects

ivEQUIPMENT LISTSStandard SupplyFR-1505 MARK-3emaNepyT.oNedoCytQskrameRrennacStinU760-4700BSR-FA21NX–110242-30PC,mm0021,mpr42760-5700BSR-FA02NX– 1019

vFR-1510 MARK-3emaNepyT.oNedoCytQskrameRrennacStinU260-4700BSR-FA21NX –1mm0021,mpr4210242-30PC,260-5700BSR-FA21NX – mm0021,mpr2410242-30PC,260-4700BS

viFR-1525 MARK-3emaNepyT.oNedoCytQskrameRrennacStinU360-4700BSR-FA02NX –110191-30PC,mm0021,mpr42360-5700BSR-FA02NX – 10191-30PC,mm0021,mpr24360-4700B

viiOptional Equipment (all models)emaNepyT.oNedoCytQskrameRreifitceR4243-UR794-030-0001 3-KRAM5251-RFroF2-B6471-UR934-030-0001yalpsiDetomeR0108-DMF–1