Furuno FA-30 Instrukcja Użytkownika

www.furuno.co.jp

21.2 AIS Receiver FA-30Mounting considerations, mountingThe FA-30 can be mounted on a desktop, deck or on a bulkhead. When selecting a mounting locati

31.3 Whip AntennaLocationThe location of the AIS VHF-antenna should be carefully considered. Digital commu-nication is more sensitive than analog/voic

41.4 WiringConnect power source, LAN cable, VHF antenna and ground wire as shownbelow.*1 Supply from breaker on switchboard.*2 If COM lines (connecti

5Attaching coaxial connector (M-P-5) to coaxial cableThe antenna cable (coaxial cable, type 5D-2V) is terminated at the FA-30 with anM-P-5 coaxial con

62. WEB SOFTWARE SETUP,DATA DISPLAYS2.1 AIS Receiver FA-30The FA-30 has no power switch. Power is fed from the ship’s switchboard, and a pow-er switch

72.2 COM Port Setup, Network SetupThe FA-30 is set up from the PC or external display. The procedure below shows how to set up the COM/POWER and NETWO

8COM port setup5. Click COM PORT Setup to show the COM Port Setup menu.6. The default setting for Data Type is IEC61162, which is suitable for most in

9NETWORK setup9. Click Network Setup to show the Network Setup menu.10.Enter the IP address assigned to the FA-30.11.Enter subnet mask for the network

102.3 Own Vessel Data Display, Channel SelectionThe Own Vessel Data display shows your ship’s MMSI no., RX channel nos., and channel selection method.

115. Click the RX Mode drop-down list to choose which channel(s) to receive.RX 1+2: Receive via channels 1 and 2.RX 1: Receive via channel 1.RX 2: Rec

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

122.4 Sensor StatusThe sensor status display provides information about sensors connected to the FA-30.1. Show the main menu, referring to section 2.2

133. MAINTENANCE,TROUBLESHOOTING3.1 MaintenanceRegular maintenance helps maintain good performance. Check the items listed below at least monthly to h

143.2 Replacing the FuseThe fuse (2A) inside the FA-30 protects it from overcurrent and equipment fault. If the unit cannot be powered, that is, the P

153.4 DiagnosticsThe built-in diagnostic facility displays program version no. and checks RAM, ROM and RX channels for proper operation.1. Open Intern

AP-1VHF CHANNEL LISTCh No. Frequency Ch No. Frequency Ch No. Frequency Ch No. Frequency1001 156.05 1088 157.425 277 156.8875 2079 161.575 1002 156.1

FURUNO FA-30 SP-1 E4443S01A SPECIFICATIONS OF AIS RECEIVER FA-30 1. GENERAL 1.1 Rx Capacity 2250 reports/minute, 1 channel

FURUNO FA-30 SP-2 E4443S01A 3. INTERFACE 3.1 COM port Input: RS422(38.4kbps)/IEC61162-1(4800 bps) Output: RS422(38.4kbps) Input sentences

D-1

Nov.28'03D-2

NAMETYPE名称kgDRAWNCHECKEDAPPROVEDDWG.No.SCALE MASS3421CBACOM/POWERDC_M(-)DC_P(+)J1212J70V12345COM_TD-ACOM_TD-BCOM_RD-ACOM_RD-BFA-30AIS RECEIVERAIS受信機(+

iIMPORTANT NOTICES• The descriptions in this manual are intended for readers with a solid knowledge of English. • No part of this manual may be copied

FURUNO ELECTRIC CO., LTD.9-52 Ashihara-Cho, Nishinomiya City, 662-8580, Hyogo, JapanTel: +81 798-65-2111 Fax: +81 798-65-4200Pub NO. DOC-929Declarat

iiWARNINGIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.CAUTIONIndicates a potentially haz

iiiCAUTIONObserve the following compass safedistances to prevent interference to amagnetic compass:Turn off the power at the switchboardbefore beginni

ivTABLE OF CONTENTSFOREWORD ...vSYSTEM CONFIGURA

vFOREWORDA Word to the Owner of the FA-30Congratulations on your choice of the FURUNO FA-30 AIS Receiver. We are confi-dent you will see why the FURUN

viSYSTEM CONFIGURATIONAIS RECEIVERFA-30HUBWHIP ANTENNASENSOROR12-24 VDCIF-1500AISORFR-8xx2 SERIESGPSSPEED LOGGYROCOMPASSSATELLITE COMPASSNAVNETRADARCH

11. INSTALLATION1.1 Equipment ListsStandard supplyOptional supplyName Type Code No. Qty RemarksAIS Receiver FA-30 - 1Installation Materials CP05-11101