Furuno FS-1562-15 Instrukcja Użytkownika

-1.2-1.2 Front View of Transceiver Unit(Same for FS-1562-15 and FS-1562-25)S/N: R0246810SH3EAGC NBSIMP1MODE2CURS3CLARIFYTX45SQ6SCANRX7TX TUNE8HI LOW9

-1.4-1.3 Power Supply UnitThe transceiver unit FS-1562-15 or FS-1562-25 works direct on 24 VDC or through a PowerSupply Unit on AC mains supply (115 o

-1.5-1.4 Starting operationThe power switch is combined with the Volume Control. Turn the Volume Control clockwise untilyou hear a click. Further cloc

-1.6-The frequencies are indicated by:Voice frequencies: Designated by the CARRIER frequency. Assigned frequencies are 1.4kHz higher than the carrier

-1.7-Direct frequency entryFree selection is possible in Dutch Version (in marine bands only).RX: To set for a receive frequency of 1636.4 kHz, for ex

-1.8-Custom channelsUp to 200 custom channels can be programmed in addition to 412 ITU channels. You can recallthem through the keyboard by channel nu

-1.9-• The [CURS (cursor)] key shifts the cursor to band or channel number.• To change the channel number, you can use the rotary control. The [FREQ/C

-1.10-1.6 TransmittingAfter selecting class of emission and frequency, youcan transmit by pressing the PTT (press-to-talk) switchon the handset or mic

-1.11-Reducing transmitter power:To conserve energy and to minimize possible interference to other stations, reduce thetransmission power. This should

C 9 - 52, Ashihara- cho, Nishinomiya, Japan Telephone: 0798- 65- 2111 Telefax: 0798- 65- 4200 Your Local Agent/Dealer All

-1.12-2. Distress calls and Distress message(1) Speak slowly and distinctly, “MAYDAY, MAYDAY, MAYDAY, pronounced as theFrench expression “m’aider”.(2)

-1.13-1.8 In the Event of Antenna Coupler FailureHIGH TENSION HAZARDDO NOT TRANSMIT WHEN ATU IS OPENEDThe Antenna Coupler automatically tunes a wire o

-1.14-1.10 ReceivingYou can select a receiving frequency by one of the following methods:- Direct frequency entry, or- Channel number entryAdjusting R

-1.15-Squelch control:Squelch is used to mute the receiver audio output when the receiver input is less than a preset valueor dominant noise is higher

-1.16-ITU channels:To select the scan group (band or channel), shift the cursor to either the position of the band orchannel number by pressing the [2

-2.1-Chapter 2 OPERATION ofOPTIONAL DEVICES2.1 Telex CommunicationTelex communication is performed with a Narrow-band direct-printing (NBDP) Terminalc

-2.2-2.2 IntercomThe intercom provides communications between the FS-1562 and the RB-500 Remote Station(option). They must be wire-connected. When int

-3.1-Chapter 3 CHANGING SYSTEMSETTING3.1 SYSTEM SETUP1. While pressing and holding down the [RCL] key, turn on the power. Release the [RCL] keywhen th

-3.2-9951 Scan/sweep-stop signal levelWhen the receiver detects a signal whose level is stronger than the preset levelit stops scanning and receives t

-3.3-9958 Squelch activating frequencySetting range: 500-2000 Hz; Factory setting 1000 Hz.9959 Sets squelch opening frequency when 2-tone alarm on 218

iiiiiiiiiiiii i"DANGER", "WARNING" and "CAUTION" notices appear throughout this manual. It is theresponsibility of the o

This page is intentionally left blank.

-4.1-Chapter 4 MAINTENANCE4.1 Weekly ChecksCheck the radiotelephone at appropriate intervals as required by Administration. For instance,Japanese Admi

-4.2-RTTIf a fault is detected, “no Good” appears instead of “Good” and the associated indication blinksafter completion of this test. Turn off the tr

-4.3-4.3 LCD/Keyboard Test & ROM Version No. Confirmation1. While pressing and holding down the [ENT] key, turn on the power. All LCD segmentsappe

-4.4-4.4 Antenna Coupler TestThe CPU and the relays which select capacitors and coils for tuning can be checked. ForCompetent technicians onlyDANGERHI

-4.5-4.5 MaintenanceThis radiotelephone equipment is designed and manufactured to provide years of intendedperformance. For this, a regular maintenanc

-4.6-Item Check Point Remedy/RemarksPower cable Check for loosened or corroded connection at power terminals.Clean and tighten.Battery Check that the

-5.1-Chapter 5 TROUBLESHOOTING5.1 Troubleshooting ListFor qualified personnel onlyThe troubleshooting list below gives common symptoms of equipmen

-5.2-TROUBLE PROBABLE CAUSE REMEDYKey input is not accepted FS-1562 is under control of external equipment"REM" appears when controlled by e

-5.3-5.2 Error IndicationWhen the FS-1562 detects a fault in the synthesizer unit (frequency unlocked), the frequency orchannel number blinks.5.3 Repl

iiDANGERDo not work inside the equip-ment unless totally familiarwith electrical circuits.Hazardous voltage which willcause death or serious injuryexi

This page is intentionally left blank.

APPENDIXCUSTOM CHANNELS/FREQUENCIES - To be programmed by Furuno DealersCH NO Ship Receive (kHz) Ship Transmit (kHz) Remarks-AP.1-

MF band working carrier frequencies - ref. US CFR 47 Part 80.371RegionShip Transmit (kHz)Ship Receive (kHz)RegionShip Transmit (kHz)Ship Receive (kHz)

MF band SSB working carrier frequenciesCH NOShip Receive (kHz)Ship Transmit (kHz)CH NOShip Receive (kHz)Ship Transmit (kHz)241 1635 2060 271 1725 2069

4/6 MHz ITU SSB carrier frequencies (ITU RR APPENDIX 16)The following frequencies are factory programmed.4 MHz SSB (J3E) 6 MHz SSB (J3E)ITU CH NO Ship

8 MHz ITU SSB carrier frequencies (ITU RR APPENDIX 16)The following frequencies are factory programmed.xelpuD-)E3J(BSSzHM8 xelpmiS-)E3J(BSSzHM8ONHCUTI

12/16 MHz ITU SSB carrier frequencies (ITU RR APPENDIX 16)12 MHz SSB (J3E) 16 MHz SSB (J3E) 16 MHz SSB (J3E)CH NO. SHIP RX SHIP TX CH NO. SHIP RX SHIP

18/19, 22, 25/26 MHz ITU SSB carrier frequencies (ITU RR APPENDIX 16)The following frequencies are factory programmed.18/19 MHz SSB (J3E) 22 MHz SSB (

TELEX CHANNELSMF BAND Telex FREQUENCY TABLEThe following frequencies are factory programmed..ONHCtimsnarTpihS)CSD,PDBN(evieceRpihS)CSD,PDBN(1020.24120

4/6 MHz BAND ITU NBDP (Telex) FREQUENCY TABLE (ITU RR APPENDIX 32)4 MHz TELEX 6 MHz TELEX 6 MHz TELEXCH NO. SHIP RX SHIP TX CH NO. SHIP RX SHIP TX CH

iiiLIST OF CONTENTSINTRODUCTION ... ivSpecifications of

8 MHz BAND ITU NBDP (Telex) FREQUENCY TABLE (ITU RR APPENDIX 32)8 MHz TELEX 8 MHz TELEXCH NO. SHIP RX SHIP TX CH NO. SHIP RX SHIP TX8001 8376.5 8376.5

12 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.12 MHz TELEX 12 MHz TELEX 12 MHz TELEXCH NO. SHIP RX SHIP

12/16 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.XELETzHM21XELETzHM61XELETzHM61.ONHCXRPIHSXTPIHS.ONHCXR

16 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.XELETzHM61XELETzHM61XELETzHM61.ONHCXRPIHSXTPIHS.ONHCXRPIH

18/19 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.XELETzHM91/81XELETzHM91/81.ONHCXRPIHSXTPIHS.ONHCXRPIHS

22 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.22 MHz TELEX 22 MHz TELEX 22 MHz TELEXCH NO. SHIP RX SHIP

22, 25/26 MHz BAND ITU NBDP (Telex) FREQUENCY TABLEThe following frequencies are factory programmed.XELETzHM22XELETzHM62/52XELETzHM62/52.ONHCXRPIHSXTP

ivINTRODUCTIONFURUNO Electric Company thanks you for selecting the FS-1562 MF/HF SSB Radiotelephone.We are confident you will discover why FURUNO has

vSpecifications of MF/HF Radiotelephone model FS-1562The model FS-1562-15/25 complies with the following rules and regulations:- IMO A.421(XI), A.610(

viFrequency Range 1.6 to 27.5 MHzInput Impedance 50 ohms (viewed from transceiver)Antenna Required 7 to 30 meters wire or whipTuning Power 10 to 20 W

-1.1-Chapter 1 OPERATION1.1 SYSTEM SET-UPThe basic 24 VDC FS-1562 consists of a Transceiver Unit, a Power Amp Unit (for 250 W), anAntenna Coupler, an