Furuno FA-150 Instrukcja Użytkownika

Installation Manual UAIS TRANSPONDER FA-150 SAFETY INSTRUCTIONS...

4 • When coaxial cable RG-10/UY (shipyard supply) is used, attach the coaxial plug M-P-7 (dockyard supply) as shown

5How to attach the plug M-P-7 Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as follows. 1. Remove the sheath by 30

6Mounting procedure 1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the coaxial connector attached to the combined box

7StanchionThe top of the stanchion comesinto contact with the flange. Installing distributor unit DB-1 The length of the cable between the distribut

81.2 Monitor Unit The monitor unit can be installed on a desktop or flush mounted in a panel. Install it on the chart table or near the steering pla

9F type Use the optional flush mount kit OP20-29. Name Type Code No. Qty Cosmetic panel 20-016-1051 100-251-370-10 1 Self-tapping screw 5x20 000-1

101.3 UAIS Transponder Mount the transponder, where it is protected from rain and water splash. This unit can be installed on a bulkhead. Install it

111.4 Power Supply (option) When selecting a mounting location for the unit, keep the following in mind: • Keep the unit out away from areas subje

122. WIRING 2.1 Connection Connect the equipment, referring to the interconnection diagram at the back this manual. GPS AntennaGSC-001 or GPS-017S

13EXT ALM: Connect ship's alarm system.DISP: Connect the monitor unit.COM4COM2COM3COM1DC (-)DC (+)COM6COM5Blue Sign Internal ports of the Transp

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANTelephone :

14*: Waterproofing connectors Wrap connector with vulcanizing tape and then vinyl tape. Bind the tape end with a cable-tie. Waterproofing connector

15How to attach wires to the WAGO connector Procedure1. Twist the cores.2. Press the terminal opener downward.3. Insert the wire to hole.4. Remove th

162.2 Changing Ship’s Mains Specifications The AC-DC power supply PR-240 is shipped ready for connection to a 200-230 VAC ship’s mains. If the ship

173. SETTING AND ADJUSTMENT After installing the equipment, set up the own ship’s static information (MMSI, IMO number, ship’s name, call sign, ty

18Selecting AIS mode The Inland AIS has two operating modes: Inland (inland waterways) and SOLAS (SOLAS compliant class A AIS transponder). Select I

193. Enter the password to show the INITIAL SETTINGS menu. Note that the password is known by only the FURUNO dealer. [INITIAL SETTINGS]SET MMSISET

203.2 Setting MMSI, IMO No., Name and Call Sign 1. Display the INITIAL SETTINGS menu referring to step 1-3 in "Setting blue sign status"

213.3 Setting GPS Antenna Position 1. Open the INITIAL SETTINGS window, referring to step 1-3 in "Setting blue status" on page 18 - 19.

223.4 Setting Ship Type 1. In the INITIAL SETTINGS window, press the ▲ or ▼ key to choose the SET SHIP TYPE and press the [ENT] key. [SET SHIP TYPE

233. Select an appropriate port among COM1, COM2, COM3, COM4, COM5 and COM6. If you chose COM1, for example, do as follows. 4. Press the [EN

iWARNINGTurn off the power at the switch-board before beginning the installation.Fire or electrical shock can result if thepower is left on.Do not in

24The table below shows the ports and corresponding items to be set. Port and data format/data transmission rate Port External device (MODE) Form

25Priority setup 1. Press ▲ or ▼ to choose SET PRIORITY at the SET I/O PORT sub-menu and press the [ENT] key. [SET PRIORITY]L/L, COG, SOGHDGROT QUI

26Quality setup (Inland AIS only) If your speed, course or heading sensor is type approved, choose quality setting as shown below. 1. Press▼ to cho

274. ATTACHING LAN KIT (OPTION) To connect to PC network or NAVNET 3D network, the optional LAN kit is required. Name: LAN kit Type: OP24-8 Code no.

28Setting LAN port for PC network 1. Press the [MENU] key, choose INITIAL SETTING, enter password, choose SET I/O PORT and press the [ENT] key to s

294. Press the [ENT] key, enter sub net mask in the SUB NET MASK field and press the [ENT] key. (Setting range: 000.000.000.000 to 255.255.255.255)

30This page intentionally left blank.

315. IEC 61162-1/2 DATA SENTENCES IEC 61162-1/2 format data is input or output from the data port COM1-COM6. The table below shows the input/output d

32Input data/Sentences Sentence (Priority) Contents ABM Addressed binary and safety related message ACA AIS regional channel assignment message A

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

iiSYSTEM CONFIGURATION : Standard : Option GPS/VHFcombined antennaGVA-100GPS antennaGSC-001GPA-017SDistributor unitDB-1VHF antennaPower supplyPR-2

%1&'016;2'%2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105+056#..

%1&'016;2'(2⇛ޓޓ࿑176.+0'ฬޓޓ⒓0#/'ᢙ㊂36;↪ㅜ㧛஻⠨4'/#4-5⇟ภ01ဳฬ㧛ⷙᩰ&'5%4+26+105#%%&apo

Antenna Cable Set CP20-02700 (004-381-160) CP20-02710 (004-381-170)A-8%1&'016;2'52+6'/010#/'1(2#46

Antenna Cable Set CP20-00300 (000-041-938) CP20-00310 (000-041-939)A-9

Y. HataiD-1

Y. HataiD-2

Y. HataiD-3

Y. HataiD-4

Mar,27'07 R.EsumiD-5

May 20 '03D-6

iiiEQUIPMENT LISTS Standard supply No. Name Type Code no. Qty Remarks 1 UAIS Transponder FA-1501 - 1 2 Monitor Unit FA-1502 - 1 GSC-001 -GPS A

Feb.22'05D - 7

Jan. 9, '03D - 8

26/Oct/09 R.EsumiD-9

Feb.02'05D-10

Nov.28'03D-11

Oct.02'03D-12

Y. HataiD-13

3412 56TYPE名前NAMEkgDWG. No.SCALEAPPROVEDDRAWNCHECKEDMASSCBDAIEC61162-2: 38.4KBPSIEC61162-1: 4800BPSFA-150U-AIS TRANSPONDERINTERCONNECTION DIAGRAM相互結線図

ivOptional supply No. Name Type Code no. Remarks 1 Monitor unit FA-1502 - CP20-02700 004-381-160 8D-FB-CV(30m)+CP20-02701 2 Antenna cable set C

11. MOUNTING NOTICEDo not apply paint, anti-corrosive sealant or contact sprayto coating or plastic parts of the equipment. Those items contain organ

2How to attach the connector N-P-8DFB for cable 8D-FB-CV Outer SheathArmorDimensions in millimeters.Inner Sheath ShieldRemove outer sheath and armo

31.1.2 VHF antenna Location The location of the mandatory AIS VHF-antenna should be carefully considered. Digital communication is more sensitive t