Furuno GP-90 Instrukcja Użytkownika

INSTALLATION MANUAL GPS NAVIGATOR GP-90 1. EQUIPMENT LIST ...

5. INITIAL SETTINGS 8 5. Press the [NU/CU ENT] key. 6. Press the [MENU ESC] key. Manual DGPS setup Enter four digit ID number, frequency and bau

5. INITIAL SETTINGS 9Input/Output Setting The GP-90 can output navigation information to external equipment. For example, it can output position da

5. INITIAL SETTINGS 10 Data format and data output availability Output data sentence of IEC 61162-1 and NMEA 0183 Ver. 1.5/2.0. AAM: Waypoint arri

5. INITIAL SETTINGS 11Input data sentence of NMEA 0183 Ver. 1.5/2.0 Checksum is checked if attached, and if any errors are found, the sentence beco

5. INITIAL SETTINGS 12 AGFPA: Autopilot information from FURUNO autopilot equipments Port Input Output DATA1 DATA2 NMEA 0183 Ver. 1.5 /2.0 AGFPA ,

5. INITIAL SETTINGS 13DATA 1 output setting 1) Press [MENU], [9] and [3]. The DATA 1, 3 OUTPUT SETUP menu appears. Talker ID GP LC DEOutput Data

5. INITIAL SETTINGS 14 DATA 2 output setting 1) Press [MENU], [9] and [4]. The DATA 2 OUTPUT SETUP menu appears. Talker ID GP LC DEOutput Data

5. INITIAL SETTINGS 15Setting DATA 4 to Data Output 1) Press [MENU], [9] and [5]. The DATA 4 I/O SETUP menu appears. DATA 4 I/O SETUP

5. INITIAL SETTINGS 16Setting DATA 4 to “COM.” (general data) Waypoints and Routes data can be received from a personal computer, through the DATA

5. INITIAL SETTINGS 1714) Output data from the computer. When loading data is completed, the cursor shifts to Stop. 15) Press the [ESC] key. Setti

SAFETY INSTRUCTIONSWARNINGDo not work inside the equipment unless totally familiar with electrical circuits.Hazardous voltage which can cause electric

186. OPTIONAL DGPSBeacon Receiver Set GR-80 GP-90GR-80DATADATA4NP Board JP3OpenTD-ATD-BRD-ARD-BGNDRD-ARD-BTD-ATD-BGND123456743217RS-422*RS-422* Thi

197. TAPING ANTENNA UNIT GPA-018S After inserting the whip antenna to the antenna base of GPA-018S, tape the antenna base and whip antenna with sel

NAME OUTLINE Q'TYDESCRIPTION/CODE №ＰＡＣＫＩＮＧ ＬＩＳＴ20AX-X-9851 -4 GP-90-**-*1-**/GP-90-DUAL-**-*1-**1/1NAME OUTLINE Q'TYDESCRIPTION/CODE №ユニット U

NAME OUTLINE Q'TYDESCRIPTION/CODE №ＰＡＣＫＩＮＧ ＬＩＳＴ20AX-X-9852 -4 GP-90-**-*O-**/GP-90-DUAL-**-*0-**1/1NAME OUTLINE Q'TYDESCRIPTION/CODE №ユニット U

CODE NO.004-372-420-00TYPECP20-01701略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-4 INSTALLATION MATERIALS工事材料表20AG-X-9405変換

CODE NO.TYPE略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-2 INSTALLATION MATERIALS工事材料表20AG-X-9404GP-80,GP-90,SC-55,GP-3500/

Apr. 18 '03D-1

Apr. 18 '03D-2

Apr. 18 '03D-3

Y. Hataihatai2005.12.19 11:57:12 +09'00'D-4

11. EQUIPMENT LIST Standards Name Type Q'ty Mass(kg) Remarks GPA-017S GPA-018S Antenna Unit GPA-019S 1 For DGPS GP-90-N Without Beacon RX D

Sep.29'05D-5

Feb. 19, '03D-6

Feb. 19, '03D-7

D-8

1A34BC2MASSkgDWG NO.DRAWNAPPROVEDSCALECHECKEDNAME名称TITLEFURUNO ELECTRIC CO., LTD.*1IV-8sq.50/60Hz,1φ220/230VAC,DPYC-1.5 *1100/110(115)/６５２１（－）（＋）PPPPP

The paper used in this manualis elemental chlorine free.FURUNO Authorized Distributor/DealerFURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,9-52

2 2. DISPLAY UNITThe display unit can be installed with either of four methods as shown below. Refer to the outline drawing at the end of manual.

33. ANTENNA UNITMounting Install the antenna unit referring to the installation diagram at end of manual. When selecting a mounting location for the

3. ANTENNA UNIT 4 How to attach the N-P-8DFB connector Outer SheathArmorInner Sheath ShieldRemove outer sheath and armor by the dimensions shown le

54. WIRINGThe figure below shows the connection of cables on rear of display unit. Ground the display unit toprevent loss of sensitivityand mutual in

4. WIRING 6 Grounding The display unit contains several CPUs. While they are operating, they radiate noise, which can interfere with other radio eq

75. INITIAL SETTINGSChecking Operation 1. Turn on the GP-90. 2. Confirm that "OK" and "BEACON RCVR INSTALLED" are displayed on