Furuno FR-2155 Instrukcja Użytkownika

MARINE RADARMODELFR-2155

1-2• The scanner unit is normally mounted with the gland side (cable entry side)facing the ship’s stern. If this direction is not possible, the gland

1-3Scanner unit assemblingThe scanner radiator and the scanner housing are shipped in separate packagesand must be assembled at installation. Assembl

1-4Scanner unit mountingThe scanner unit should be assembled before hoisting it to the mounting platform.When using a crane or hoist, lift the unit b

1-5Seal washerCorrosion-proof rubbermatHex boltHex nutSpring washerFlat washerGroundwireFlat washerHex boltHex nutSpring washerFlat washerGroundwireS

1-61.2 Display UnitBefore mounting the display unitIf Gyro Converter GC-8 (option) is to be used, install and setup the GYRO CON-VERTER Board before

1-74. While one person is holding the mounting base at the sides, pull the handle onthe underside of the control head to draw the display unit toward

1-8b)While pushing the stopper, set the catch on the display unit in the hole at thefront edge of the stay.CatchStopperStayFigure 1-7 Setting catch t

1-9J105J104J103J466J462J465*Screw(M3x8, 5 pcs.)****Slide forward.Screw (M4x8, 2 pcs.)Fixing hole (front)Fixing hole (rear)KnobFigure 1-9 How to remov

1-10Separate Control Head Kit (Type: OP03-151, No.: 008-485-530)emaNepyTytQ.oNedoCskrameR.yssAelbaCP1/P02BS642LU1218-041-0002249S30,m01eldnaH4-C-2401

1-118. Unfasten four screws fixing the right and left brackets on the control head.9. Unfasten four screws fixing the right and left covers on the di

C 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 Your Local Agent/Dealer All rights re

1-12KB BOTTOMPLATEP312 FX ConnectorP314 XH3PJ312 (underside)J314 (underside)ScrewM4X8 (8 pcs.)Pan-head Screw M4X8 (2 pcs.)Be careful not to pinch c

1-138. Lower the monitor.9. Attach the monitor front cover (option) to the place the panel cover have been,using the screw for the panel cover.10.Att

1-141.3 Power Supply UnitsThe Power Supply Unit PSU-001 (for scanner unit) and PSU-004 (for display unit)do not contain usual operating controls. The

2-1WIRING2.1 Scanner UnitPreparationsOpen the port side cover of the scanner unit to access terminal boards.Fabricating signal cable S03-801. Shorten

2-26. Determine the length of each core considering its location on STB-1 in thescanner unit (see the interconnection diagram on page S-1). Remove ap

2-3Fabricating signal cable 250V-MPYCY-16 (JIS cable)1. Unfasten the clamping gland from the upper cable gland, and remove thegasket and flat washers

2-47. Secure the clamping gland to the cable gland body; then seal with putty.8. Connect the conductors to STB-2 and STB-3, referring to the intercon

2-52.2 Display UnitTwo cables are terminated at the display unit: the signal cable S03-80 and thepower supply cable from the Power Supply Unit PSU-00

2-6Leading in cables to the display unitThe cable clamp may be positioned within the display unit (default arrangement),outside the display unit. Whe

2-7Cable fed from outside display unit(B) Power clamp(Aluminum)(C) Signal clamp(Aluminum)(D) Rear clamp plate(A) Rear clamp baseBottom clamp front pl

iSAFETY INSTRUCTIONSDo not open the equipmentunless totally familiar withelectrical circuits andservice manual. Only qualified personnel

2-8ConnectionsOpen the display unit and fix it with the stay. (For procedure see page 1-6.)Remove the shield cover from the INT Board. Connect signal

2-9Connectors on the INT BoardTable 2-1 Connectors on the INT BoardemanlangiSnoemaNbcprotcennoC.onrotcennoCepytelbacilppAtnempiuqeskrameRlangiStupnIl

2-10How to attach NH connector20mm1 Insert NH connectorwire into NH connectorhousing.2 Cut shrink tubingin 20 mm lengths andslip onto each wire.3 Sol

2-112.4 Power Supply UnitsPower supply unit PSU-004Thermal relayK2Relay K3Relay K1TBPTB12TBPTB13TBPTB11TBPTB14Photo No. 3148Figure 2-15 Power supply

2-12Power supply unit PSU-001Two cables run to the Power Supply Unit PSU-001, the power cable (DPYCY-3.5) and the signal cable (660V-MPYCY-16). The f

3-1INITIALIZATION AND ADJUSTMENT3.1 Tuning InitializationTune the radar as follows: Press [RADAR MENU] [0] [0] [2] [0] [0] [0] [0] (TUNEINITIALIZE on

3-23.4 Heading AlignmentYou have mounted the scanner unit facing straight ahead in the direction of thebow. Therefore, a small but conspicuous target

3-33.5 Adjusting Sweep TimingSweep timing differs with respect to the length of the signal cable between thescanner unit and the display unit. Adjust

3-43.7 Confirming Magnetron Heater VoltageMagnetron heater voltage is adjusted at the factory using a 15 m signal cable.Therefore, when the length of

3-5 Fuse801R813Photo No. 2914Figure 3-6 Scanner unit, power supply unit PSU-001Note: When the length of the cable between the scanner unit an

iiCAUTIONObserve the following compass safedistances to prevent deviation of amagnetic compass:Ground the equipment toprevent electrical shock andmutu

3-63.8 Initial Setting MenusThe INITIAL SETTING menus (four menus) and the OWN SHIP INFORMATIONmenu setup the radar according to expected usage, auth

3-7INITIAL SETTING1 menuKeying sequence: [RADAR MENU] [0] [0] [0] [2]HL ALIGN: Aligns heading.TIMING ADJ: Adjusts sweep timing.ANT HGT: Enter height o

3-8HEAD UP TB SCALE: Bearing scale may be shown in degrees or compasspoints in the head-up mode.CTR ECHO STRETCH: Turn on to enlarge echoes in the ran

4-1INSTALLATION OF OPTIONAL EQUIPMENT4.1 Gyro Converter GC-8The Gyro Converter GC-8, incorporated inside the radar display unit, convertsanalog gyroc

4-24) Connect the GYRO CONVERTER Board to the INT Board (cables suppliedwith GC-8) as shown below.INT Board GYRO CONVERTER BoardJ446

4-3Connection of external power supplyAn external power supply is necessary when the repeater signal is step-by-steptype and the step voltage is belo

4-4Setting method 1: by gyrocompass specifications1) Gyrocompass type 2) FrequencyGyrocompasstypeSW1-4SW1-5SW1-6JP1 Frequency SW1-7SW1-8RemarksAC syn

4-5Setting method 2: by make and model of gyrocompassrekaMsledoMnoitacificepSWS1-1WS2-1WS3-1WS4-1WS5-1WS6-1WS7-1WS8-1WS1-2WS2-2WS3-21PJ2PJ3PJ4PJ5PJON

4-6Location of DIP switches, jumper wires on the GYRO CONVERTERBoard64P1106JP5, JP4(Supply voltage)JP2(Rotor voltage)JP3(Stator voltage)JP1(Gyro type

4-74.2 ARP Board ARP-26The ARP Board ARP-26, which provides ARPA functions, is an optional circuitboard which is accommodated in the display unit of

iiiTABLE OF CONTENTSEQUIPMENT LISTS... ivSYSTEM CONFIG

4-8ARP board adjustment1. Turn the GAIN, A/C SEA and A/C RAIN controls fully counterclockwise, andthen transmit on the 12 nm range.2. Connect a digit

4-9Final checkConnect a gyrocompass and a log to the radar and place the radar under transmitstate. Confirm that LEDs CR9, CR10, CR11, CR12, CR15 and

4-104.3 RP Board RP-26The RP Board RP-26, which providesvideo plotter functions, consists of a circuitboard and a card drive both of which are accomm

4-114. Unfasten the front panel from the display pedestal.5. Pass the connector from the card case through the hole in the display pedestal.Display p

4-1210.Fasten the front panel on the display pedestal.11.Retract the stay to close the display unit.12.Fasten the right arm cover.Separate type contr

4-13M-card baseM-cardcase lidPan Head ScrewM2.6X5(2 pcs.)Control sectionControl sectionfront panelFigure 4-13 Display pedestal, front view5. Loosen s

4-1410.Fasten the front panel of the display pedestal.11.Fasten the ground wire to the location shown in Figure 4-14.12.Close the monitor.4.4 Perform

4-154.5 Alarm KitNecessary parts: OP03-156 (Code no. 008-500-650)The alarm kit mainly consists of a circuit board and connection cables, and pro-vide

4-16J475J474J473J472J471J451AAPan-head ScrewM3X8, 4 pcs.Cable Tie CV-100,2 pcs.ALARM Board03P9262NH Connector03-1991(3P), 4 pcs.Pan-head screwM4X12 C

ivEQUIPMENT LISTSStandard SupplyemaNepyT.oNedoCytQskrameRtinUrennacSN-9400-BSR-A4NX–1,CAV022/002,reciedon,mm07523 ,φ W051I-9400-BSR-A4NX–,CAV022/002,

vOptional EquipmentemaNepyT.oNedoCytQskrameRyalpsiDetomeR0108-DMF – 1retrevnoCoryG2-8-CG025-644-800tes1redroetarapeS1-8-CG072-644-800nitliuBhctiwsret

viSYSTEM CONFIGURATIONDISPLAY UNITRDP-124ARPA BoardARP-26NavigatorIEC 61162-1 (Input/Output)IEC 61162-1 (Input)Speed LogOPTIONPerformanceMonitorPM-30

1-1MOUNTING1.1 Scanner UnitMounting considerations• The scanner unit is generally installed either on top of the wheelhouse or on theradar mast, on a