Furuno FR-2115-B Instrukcja Użytkownika

i Installation Manual MARINE RADAR FR-2115-B/FR-2125-B SAFETY INSTRUCTIONS... i EQUIPMENT LISTS ...iii SYSTE

1-2 1.1.2 Assembling the antenna unit The antenna unit consists of the antenna radiator and the antenna unit chassis, and they are packed separatel

1-3 O-ringRadiator bracketWaveguideAntenna radiatorHex bolt (M8X40), 8 pcs.(XN20AF, XN24AF only) Guide pin(XN20AF,XN24AFonly)Hex bolt (M8X35), 8 pcs

1-4 1.1.3 Fastening the antenna unit to the mounting platform The antenna unit may be assembled before hoisting it to the mounting platform. Howeve

1-5 Ground the equipment toprevent electrical shockand mutual interference.CAUTION Figure 1-4 How to mount the antenna unit

1-61.2 Processor Unit1.2.1 Mounting considerationsWhen selecting a mounting location, keep in mind the following points:• The processor unit must be

1-7 1.2.2 Mounting the processor unit 1. Drill four holes of 12 mm in diameter in the mounting location. 2. Unfasten 15 binding screws (M4) to re

1-8 J106J105J104J103J446J466J462J465*Screw(M3X8, 5 pcs.)****Slide forward.Screw (M4X8, 2 pcs.)Fixing hole (front)Fixing hole (rear)KnobPan-headScre

1-91.3 MonitorThe FR-2115-B/2125-B is available with or without a monitor. This section shows how to mountthe monitor supplied.Mounting consideration

1-10 1.3.2 Mounting the monitor 1. Drill four holes of 12 mm in diameter in the mounting location, referring to the outline drawing for mounting

1-11 1.4 Control Unit 1.4.1 Mounting procedure 1. Attach rubber to feet to the bottom of the keyboard if the keyboard is not going to be permanentl

C 9-52, Ashihara-cho, Nishinomiya, Japan Telephone: 0798-65-2111 Telefax: 0798-65-4200 Your Local Agent/Dealer All rights re

2-1 2. WIRING 2.1 Antenna Unit Transceiver module(magnetron inside)Height morethan 5 cmNon-ferrous blockThe magnetron in the transceiver module will

2-2 4. Unfasten the four fixing bolts on the cable gland at the base of the antenna unit. Remove clamping ring, rubber gasket and washers. From left

2-3 12. If the antenna is mounted 2° or more left of ship's bow, adjust the position of S901 so it becomes "on" (contact between #1 a

2-4 2.1.2 Fabricating signal cable S03-75 1. Remove the vinyl sheath by 450 mm. 2. Slide the clamping ring, washer, rubber gasket and washer onto

2-5 2.2 Processor Unit Two cables are terminated at the processor unit: the signal cable S03-75 and the power cable. The signal cable comes with a c

2-6 2.2.2 Fabricating the DC power cable (CVV-S 8X2C, option) 1. Remove the vinyl sheath by 100 mm. 2. Unravel the braided shield 60 mm from end

2-7 2.2.3 Leading in cables to the processor unit Cables are led in to the processor unit through the cable clamp at the rear of the unit. Use the

2-8 2.3 Monitor 2.3.1 Connection of monitor cable inside processor unit The monitor cable (a monitor cable comes with FURUNO-supplied monitor) runs

2-9 2.3.2 Connection of monitor cable inside the monitor Connect the monitor cable inside the monitor as below. MONITORREARVIEWLoosen two M4X10pan-

2-10 2.4 Control Unit 1. Open the processor unit. 2. Lead in the control unit cable assy. (option) from the rear entrance of the processor unit. 3

iSAFETY INSTRUCTIONSWARNINGRadio Frequency Radiation HazardThe radar antenna emits electromagnetic radio frequency (RF) energy which can beharmful, pa

2-11 2.5 External Equipment Open the processor unit. Remove the cover from the INT Board. Connect signal, power (ship's mains and power supply)

2-12Connectors on the INT BoardTable 2-1 Connectors on the INT BoardSignalNameName onPCBConnectorNo.ConnectorTypeApplicableEquipmentRemarksINPUT SIGNA

2-13 How to attach NH connector 20mm1) Insert NH connectorwire into NH connectorhousing.2) Cut shrink tubingin 20 mm lengths andslip onto each wire

3-1 Figure 3-1 Processor unit, cover opened 3. INITIALIZATION AND ADJUSTMENT 3.1 Tuning Initialization Tune the radar as follows: Press [RADAR MENU]

3-2 3.4 Heading Alignment You have mounted the antenna unit facing straight ahead in the direction of the bow. Therefore, a small but conspicuous tar

3-3 3.5 Adjusting Sweep Timing Sweep timing differs with respect to the length of the signal cable between the antenna unit and the processor unit.

3-4 3.7 Confirming Magnetron Heater Voltage Magnetron heater voltage is adjusted at the factory. However, confirm that it is within the prescribed r

3-5 3.8 Initial Setting Menus The INITIAL SETTING menus (four menus) and the OWN SHIP INFORMATION menu setup the radar according to expected usage,

3-6INITIAL SETTING1 menuKeying sequence: [RADAR MENU] [0] [0] [0] [2]HL ALIGN: Aligns heading.TIMING ADJ: Adjusts sweep timing.ANT HGT: Enter height o

3-7INITIAL SETTING3 menuKeying sequence: [RADAR MENU] [0] [0] [0] [2] [0] [0]TRAILS RESTART: Selects whether to restart or discontinue target trails w

iiDo not open the equipmentunless totally familiar withelectrical circuits andservice manual. Only qualified personnel should work insid

4-1 1. OPTIONAL EQUIPMENT 4.1 Gyro Converter GC-8 The Gyro Converter GC-8, incorporated inside the processor unit, converts analog gyrocompass read

4-2 4. Connect the GYRO CONVERTER Board to the INT Board (cables supplied with GC-8) as shown below. INT Board GYRO CONVERTER Board

4-3 4.1.2 Connection of external power supply An external power supply is necessary when the repeater signal is step-by-step type and the step volt

4-4Setting method 1: DIP switch settings and gyrocompass specifications1) Gyrocompass type 2) FrequencyGyrocompasstypeSW1-4

4-5 Setting method 2: DIP switch/jumper settings and make and model of gyrocompass rekaMsledoMonitacificepSSW1-1WS2-1WS3-1WS4-1WS5-1WS6-1WS7-1WS8-1W

4-6 Location of DIP switches, jumper wires on the GYRO CONVERTER Board 64P1106JP5, JP4(Supply voltage)JP2(Rotor voltage)JP3(Stator voltage)JP1(Gyro

4-7 4.2 ARP Board ARP-26 The ARP Board ARP-26, which provides ARPA functions, is an optional circuit board which is accommodated in the processor u

4-8 4.2.2 ARP board adjustment 1. Turn the GAIN, A/C SEA and A/C RAIN controls fully counterclockwise (OFF). Transmit on the 12 nm range. 2. Conn

4-9 4.2.3 Final check of ARP board Connect a gyrocompass and a log to the radar and place the radar under transmit state. Confirm that LEDs CR9, CR

4-10 2. Unfasten four M3X8 pan-head screws to remove the RP board mountlng plate from the RGB board and its mounting plate. J106J105J104J103J446J

iii EQUIPMENT LISTS Standard supply (System with monitor) Name Type Code No. Qty Remarks XN12AF-RSB-0074-062 − FR-2115-B, 24 rpm, 1200 mm XN12AF-

4-11 4. Fix the M-card base assy. with two M3X8 pan-head screws. 5. Set the M-card case cover to the hole in the front panel and fix with two M2.6

4-12 8. Run the connector from the card case in front of the GYRO CONVERTER Board as shown in Figure 4-12. 9. Plug the connector from the M-card b

4-13 4.4 Performance Monitor PM-30 Necessary parts: PM-30 and OP03-150 (Code no. 008-485-490) Name Type Code No. Qty PM-IN Board 03P9225 008-487-

4-144.5 Alarm KitThe alarm kit mainly consists of a circuit board and connection cables, and provides alarm outputto ship's bridge alarm system.N

4-15 J472: ARPA guard zone; target alarm J473: SYSTEM FAILURE (HP, BP, TRIG, VIDEO, GYRO, and AZI) J474: ARPA CPA/TCPA J475: Spare J475J474J473J472J

4-16 1. Open the processor unit. 2. Follow a) and b) of "how to access rear-left fixing hole" on page 7 to remove the PTU Board cover. 3

iv Standard supply (System without monitor) Name Type Code No. Qty Remarks XN12AF-RSB-0074-062 − FR-2115-B, 24 rpm, 1200 mm XN12AF-RSB-0075-062 − FR

v Optional equipment Name Type Code No Qty Remarks Remote Display FMD-8010 − 1 GC-8-2 008-446-520 Separate order Gyro Converter GC-8-1 008-446-

viSYSTEM CONFIGURATIONOptionFR-2115-B: XN12AF-RSB-0074-062 XN12AF-RSB-0075-062 XN20AF-RSB-0074-062

1-1 1. MOUNTING1.1 Antenna Unit1.1.1 Mounting considerations• The antenna unit is generally installed either on top of the wheelhouse or on the rada