Furuno NETCONTROLLER B042-008 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt powietrzny Furuno NETCONTROLLER B042-008. Furuno NETCONTROLLER B042-008 User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj

Podsumowanie treści

Strona 1 - COLOR LCD SOUNDER

COLOR LCD SOUNDERFCV-1100LBack

Strona 2 - *IME23670C20**IME23670C20*

EQUIPMENT LISTS viii 3 kW transducer Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel TFB-7000 (2) T-681 28/50 FRP 28F-24H, 50F-2

Strona 3 - SAFETY INSTRUCTIONS

EQUIPMENT LISTS ix1 kW/2 kW transducer Output (W) Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - 28/50 FRP 28F-8 50B-12 - - S

Strona 4 - 0.7 m 0.5 m

EQUIPMENT LISTS x 1 kW/3 kW transducer Output (W) Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - 28/45 FRP 28F-8 45F-12H -

Strona 5 - TABLE OF CONTENTS

EQUIPMENT LISTS xi Output (W) Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - FRP 50B-6/6B 200B-12H - - Steel - - FRP 50B-9/9B

Strona 6 - SYSTEM CONFIGURATION

EQUIPMENT LISTS xii 2 kW/3 kW transducer Output (W) Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - 28/45 FRP 28F-18 45F-12H

Strona 7

EQUIPMENT LISTS xiii3 kW/2 kW transducer Output (W) Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - 28/50 FRP 28F-24H 50B-12 -

Strona 8 - Available transducers

EQUIPMENT LISTS xiv This page is intentionally left blank.

Strona 9 - 2 kW transducer

1-11. MOUNTING 1.1 Display Unit WARNINGTurn off the power at the switchboardbefore beginning the installation.Fire or electrical shock can result i

Strona 10 - EQUIPMENT LISTS

1. MOUNTING 1-2 Mounting procedure Desktop mounting 1. Loosen two M6 x 25 bolts at the front of the display unit to remove the mounting base. M6 x 2

Strona 11 - 1 kW/2 kW transducer

1. MOUNTING 1-3Flush mounting 1. Make cutout in mounting location referring to the outline drawing show below. 2. Fasten the display unit to the mo

Strona 12

Your Local Agent/DealerYour Local Agent/Dealer9-52 Ashihara-cho,9-52 Ashihara-cho,Nishinomiya, JapanNishinomiya, JapanTelephone :Telephone : 0798-65-2

Strona 13

1. MOUNTING 1-4D>50 cmD5X20Flush with hull bottom1.2 Transducer The performance of the video sounder depends upon the transducer position. A place

Strona 14

1. MOUNTING 1-5Thru-hull mount water temperature sensor T-02MSB, T-03MSB • Select a suitable mounting location considering the following points: •

Strona 15

1. MOUNTING 1-6Through-hull mount water temperature/speed sensor ST-02MSB, ST02-PSB Select a suitable mounting location considering the following:

Strona 16

2-12. WIRING Refer to the interconnection diagram at the back of this manual for detailed information. Wiring diagram for standard-type FCV-1100L

Strona 17 - 1. MOUNTING

2. WIRING 2-2 2.1 Wiring Standard Equipment Transducer Separate the transducer cable well away from power cables to prevent interference. Connect th

Strona 18 - Desktop mounting

2. WIRING 2-32.2 Wiring Optional Equipment Navigator Use cable type MJ-A6SPF0011/0012 (option) to connect the navigator to the NMEA connector. Wate

Strona 19

2. WIRING 2-4 This page is intentionally left blank.

Strona 20 - 1.2 Transducer

3-13. INITIAL SETTING This section provides the information necessary for initial setup of the equipment. First turn on the power and set display la

Strona 21 - T-02MSB T-03MSB

3. INITIAL SETTINGS 3-2 3.2 Transducer Data CAUTIONSet the transducer model numberproperly.Wrong transducer setting can damage thetransducer and void

Strona 22 - ST-02MSB, ST02-PSB

3. INITIAL SETTINGS 3-3Entering transducer data by transducer model number Note 1: If you are continuing from paragraph 3.1 go to step 2. Note 2: If

Strona 23 - 2. WIRING

i SAFETY INSTRUCTIONSWARNINGTurn off the power at the switchboardbefore beginning the installation.Fire or electrical shock can result if thepower i

Strona 24 - Power cable

3. INITIAL SETTINGS 3-4 3. Press [!] to select [HIGH] CONNECTION or [LOW] CONNECTION (whichever is installed), and then press [+] or [-] to show the

Strona 25 - 2.3 Input/Output Sentences

3. INITIAL SETTINGS 3-5Transducer setting Change the terminal board setting at the rear of the display unit according to the transducer connected. N

Strona 26

3. INITIAL SETTINGS 3-6 Entering transducer data by transducer specifications For dealer: When connecting the transducers which are not programmed, c

Strona 27 - 3. INITIAL SETTING

3. INITIAL SETTINGS 3-7d) Use [+] or [-] to set the value for the frequency which is connected, and then press [!] or ["] to close the dialog bo

Strona 28 - 3.2 Transducer Data

3. INITIAL SETTINGS 3-8 6. Press ["] to select TEMP INPUT, and then press [+] or [-] to open the dialog box. SENSOR NMEA 7. Use [+] or [-] t

Strona 29 - Installation main menu

3. INITIAL SETTINGS 3-93.4 Nav Data, Heading Sensor Setting Select navigator and heading sensor used as below. 1. Turn on the power and turn the [

Strona 30 - Scroll bar

3. INITIAL SETTINGS 3-10 Adjustment value = Actual value - Indication of FCV-1100LActual value x 100 (%) c) Press [!] or ["] to close the dialog

Strona 31 - Transducer setting

3. INITIAL SETTINGS 3-113.5 Propagation Velocity This section provides the information for adjustment of propagation velocity. Normally, no adjustmen

Strona 32 - 3. INITIAL SETTINGS

3. INITIAL SETTINGS 3-12 3.6 Demonstration Mode The demonstration mode provides a simulated video sounder picture. Connection of the transducer is no

Strona 33

3. INITIAL SETTINGS 3-133.7 Restoring Default Settings The procedure below restores most default settings. Are not affected: target setting, languag

Strona 34

ii CAUTIONObserve the following compass safedistances to prevent interference to amagnetic compass:Ground the equipment toprevent mutual interfere

Strona 35

This page is intentionally left blank.

Strona 36

AP-1 APPENDIX 1 TRANSDUCER 50BL-12/50BL-24H When using the transducer 50BL-12/50BL-24H, see this appendix. Transducer, thru-hull pipe and tank lis

Strona 37 - 3.5 Propagation Velocity

AP-2 APPENDIX 2 NEW BLT TRANSDUCERS A new type BLT transducer (Bolt-clamp Langevin Transducer) has been developed for this echo sounder. The BLT t

Strona 38 - 3.6 Demonstration Mode

APPENDIX 2 NEW BLT TRANSDUCERS AP-3 Steel T-682 (000-015-851)TWB-6000 (2) (000-015-207) TFB-7000 (2) (000-015-209) 50/88 50BL-24HR/88-126H FRP T-682F

Strona 39

APPENDIX 2 NEW BLT TRANSDUCERS AP-4 This page is intentionally left blank.

Strona 44

Nov. 14, '02D - 4

Strona 45

iii TABLE OF CONTENTS SYSTEM CONFIGURATION... iv EQUIPMENT LISTS ...

Strona 49 - Nov. 14, '02

iv SYSTEM CONFIGURATION

Strona 50

EQUIPMENT LISTS v EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display unit CV-1100L - 1 Spare Parts SP02-04401 001-402-100

Strona 51

EQUIPMENT LISTS vi Available transducers 1 kW transducer Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel - - FRP 28F-8 50B-6/6B -

Strona 52

EQUIPMENT LISTS vii2 kW transducer Frequency (kHz) Hull Material Transducer Thru-Hull Pipe Tank Steel TFB-7000 (2) T-634 28/50 FRP 28F-18 50B-12 - -

Komentarze do niniejszej Instrukcji

Brak uwag